You are not logged in.

- Topics: Active | Unanswered

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

Suppose I have a pipe that is bent to a degree, measuring the length of the pipe from the top to the bottom at 11.76cm. I want to know the length of the pipe as if there was no bend ?

Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

What do you mean by angle? What is the thickness of the pipe? What are the inside and outside diameters?

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**anonimnystefy****Real Member**- From: The Foundation
- Registered: 2011-05-23
- Posts: 15,380

You also need the angle of the bend.

Here lies the reader who will never open this book. He is forever dead.

Taking a new step, uttering a new word, is what people fear most. ― Fyodor Dostoyevsky, Crime and Punishment

Offline

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

That is all the information I can retrieve. The pipe is 11.76cm measuring from the top of the pipe to the bottom including the bend. I want the length of the pipe, as though the pipe is stretched out.

*Last edited by SuperLynx (2013-11-20 06:46:56)*

Offline

**anonimnystefy****Real Member**- From: The Foundation
- Registered: 2011-05-23
- Posts: 15,380

You mean, direct distance from one end to the other?

Here lies the reader who will never open this book. He is forever dead.

Taking a new step, uttering a new word, is what people fear most. ― Fyodor Dostoyevsky, Crime and Punishment

Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

Top of the pipe to the bottom? What does that mean?

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

anonimnystefy wrote:

You mean, direct distance from one end to the other?

Direct Length.

The white is the pipe. From Top > Bottom measured.

Offline

**anonimnystefy****Real Member**- From: The Foundation
- Registered: 2011-05-23
- Posts: 15,380

Then you need at least the angle of the bend.

Here lies the reader who will never open this book. He is forever dead.

Taking a new step, uttering a new word, is what people fear most. ― Fyodor Dostoyevsky, Crime and Punishment

Offline

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

What if I don't have the angle, there is no other solution, I must have the angle ?

Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

Is that to scale?

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**bob bundy****Moderator**- Registered: 2010-06-20
- Posts: 6,311

You'll have to say something else about this pipe eg diameter perhaps

See picture below. Three very different lengths but all have the same top to bottom measurement.

Bob

You cannot teach a man anything; you can only help him find it within himself..........Galileo Galilei

**Online**

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

The diameter is

. If you really need the angle measurements, I'll get those numbers. I'm really hoping there is a genius way to figure it out without finding out the length of the object, which includes pipe length followed by the angle of the bend measurements.Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

I do not think that is helping enough.

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**anonimnystefy****Real Member**- From: The Foundation
- Registered: 2011-05-23
- Posts: 15,380

Will it bend?

Here lies the reader who will never open this book. He is forever dead.

Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

The pipe? I guess it should. How does that help?

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**anonimnystefy****Real Member**- From: The Foundation
- Registered: 2011-05-23
- Posts: 15,380

Dunno, maybe we should ask Bender.

I just got an idea. How about posting a picture of the pipe. We might be able to get the other measurements needed.

Here lies the reader who will never open this book. He is forever dead.

Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

I asked him if that was to scale then I would just measure it. Since he is not providing any numbers a measurement would be better than a calculation.

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**anonimnystefy****Real Member**- From: The Foundation
- Registered: 2011-05-23
- Posts: 15,380

The picture above is a picture in a paint program, so my bet is that it is definitely not to scale. An actual picture would do just fine, though.

I am also wondering, what is the motivation behind this?

Here lies the reader who will never open this book. He is forever dead.

Offline

**bobbym****Administrator**- From: Bumpkinland
- Registered: 2009-04-12
- Posts: 84,526

I am not sure. But it also does not look like a pipe...

I have the result, but I do not yet know how to get it.

All physicists, and a good many quite respectable mathematicians are contemptuous about proof.

Offline

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

The image is suppose to represent a pipe, use your imagination. I gave the measurements from top to bottom, the top would be the top of the pipe as seen in the image, the bottom, obviously the bottom of the pipe. Is there a formula to find out the length of the pipe as though the pipe did not have a bend, and was straight, or must the measurements of the bend of the pipe be known ?

Offline

The question seems to be unclear and the diagram is even more.

'And fun? If maths is fun, then getting a tooth extraction is fun. A viral infection is fun. Rabies shots are fun.'

'God exists because Mathematics is consistent, and the devil exists because we cannot prove it'

'Humanity is still kept intact. It remains within.' -Alokananda

Offline

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

I said the question in post #20 !

Offline

Does the pipe represent a chord? Yes?

Where did you get such a question from?

'And fun? If maths is fun, then getting a tooth extraction is fun. A viral infection is fun. Rabies shots are fun.'

'God exists because Mathematics is consistent, and the devil exists because we cannot prove it'

'Humanity is still kept intact. It remains within.' -Alokananda

Offline

**SuperLynx****Member**- Registered: 2009-06-28
- Posts: 286

A chord, where would you get such an idea from, it's a rough pipe, sketch.

Offline

sorry, I meant: Does the pipe represent an arc?

'And fun? If maths is fun, then getting a tooth extraction is fun. A viral infection is fun. Rabies shots are fun.'

'God exists because Mathematics is consistent, and the devil exists because we cannot prove it'

'Humanity is still kept intact. It remains within.' -Alokananda

Offline