But I wonder what it is 12% of ???

I'll research Illustrator and see if i can find out.

LATER EDIT: As far as I can tell that warp feature does not allow you to control the shape in the way you want. The top and bottom curves must be arcs of a circle and concentric for the label to fit. Adobe don't tell you 'exactly' what warp does, but the curves may not be parts of a circle.

You can draw circles (ie radius L) and position straight lines to cut out a sector. Then you'd have to edit the shape outline to limit it to the sector you want. I've never used Illustrator, but that's how I'd do it.

Bob

]]>The preview option doesn't show the images. I don't know why? Then it forgets them when you submit.

So try an image upload and submit without a preview.

Anyway, I've been busy and made a spreadsheet. The screen shot of my figures is shown below (hopefully, if it works for me!!!)

The bordered boxes are the ones you would enter values. The rest get worked out by my formulas.

Using your diameters 10.125 and 8.5, the height of the pot 9.125, the distance down from top to label 0.75 and distance up from bottom to label 1.0 the calculated values are L = 46.1337 and percentage = 10.9735

There are plenty of places where I might have slipped up so I cannot guarantee it is bug free. What I suggest is for you to try these values, print off a trial and see if it fits. Let me know and I'll either whoop with amazement or drop to the floor sobbing, depending on your answer.

If it does work then I can do a second screen shot showing the formulas, which you will then have to copy carefully into your own sheet.

It's gone midnight now in the UK so I'm off to bed. I'll check in the morning in about 8 hours.

Bob

]]>I do appreciate the help SO much! Hey if you need any design work like business cards or invitations to something or whatever, let me know! THAT I can do!

PS

Tried again to upload screen shot jpg and it's not showing in preview.

For screen shots in a Windows operating system I do 'prt sc' for print screen, paste the result into Paint, cut out the bit I want, re-paste into a new Paint screen and save as a .GIF.

When you want to reply with a picture, make sure you click bottom right on 'post reply' not the 'quick reply' option as this doesn't have an Image Upload option.

I'll start work on my Excel sheet.

Bob

]]>Another figure you might need is that the label will be .75 from the top of the pot

Oh boy that changes everything! The radius for the label isn't 5.0625 at all because your label isn't at the top! And if I start with a pot height of 9.125 and take off 0.75 that leaves 8.375. But you say the label is 7.375. So is there an inch below the label at the bottom?

I can use proportion to calculate the right radiuses (radii) but I need to be certain the label is 1 inch from the bottom.

Once I'm sure of the right radiuses I can work out s, L and the percentage. Do you have Excel or some similar spreadsheet program. Because I could give you the formulas in that format and then you've got it sorted for any other size pot. Just plug in the figures and it'll pop up with the answers.

Bob

]]>Bob

]]>Let's see if I can take you through this one step at a time.

Step 1. What shape do you need to make the label?

Have a look at my diagram below. It shows a large circle with a smaller one inside. And I've drawn two straight lines out from the centre. Two arcs plus the two lines make a sector of the circle. I've coloured the sector using red and pink. Try this with a bit of paper. Don't worry about sizes at the moment. Any size will do.

Cut out the sector (both bits, still joined). Fold it round until the straight lines meet. You should have a cone.

Cut off the pink bit. Re-fold. You should have a cone with the top cut off. (technical name: frustrum)

That's the shape you need.

Step 2. How big must the circle be to make the frustrum?

Now I'm assuming you will know the radius of the top and the bottom. Your values in the last post are correct.

You also need to know how far along the paper it is from the top circle to the bottom circle. This is the slant height along the pot. It is not the same as the vertical height.

I've shown these measurements in the second diagram

Now the distance from the centre to the small circle (L-s) as a fraction of the distance to the big circle is

The small circle is the same fraction of the large circle:

So these fractions are the same.

If that's starting to get confusing, try it with some numbers.

Suppose the small circle is 1/3 of the large circle.

But the distance L-s has to be one third of L. So

Let's say s = 10 inches.

If L-s is one third of L, then s must be two thirds of L. So

check: If L = 15 and s = 10 then L-s = 5 and 5 is one third of 15 tick.

So the formula for calculating L is

Now I've done some algebra to get L = something in this equation. Maybe that's too much for you so here it is with those numbers:

step 3. So what fraction of the whole circle do we need to make this frustrum?

The arc at the bottom is 2 x pi x R1

The whole circle is 2 x pi x L

So the angle is this fraction of a whole circle:

Now I multiplied that fraction by 360 degrees. If your software wants a percentage then I think you need:

Hope that does it.

Bob

]]>